Power - 3000 Watts Max x 1 @1-Ohm, 1500 Watts Max x 1 @2-Ohms
Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
Strapping Capable - You are able to strap TWO PL3000.1D amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power
power: max power output of 1500 watts at 2 ohms into one channel. maximum power output of 750 watts at 4 ohms into one channel. this amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
high level inputs: speaker level inputs are commonly referred to as high-level inputs. this input will be used to connect the ac1500.1m to your factory radio or aftermarket radio that does not have low-level (rca) inputs
low level inputs: line level inputs, also known as rca inputs or low-level inputs, use rca interconnect cables to link the ac1500.1m with the source unit. most aftermarket radios have multiple pairs of rca outputs that can connect to multiple amplifiers
low-pass crossover: a low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. a low-pass filter will primarily keep high notes out of your subwoofer(s)
Power - 1500 Watts Max x 1 @2-Ohms, 750 Watts Max x 1 @4-Ohms
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
Power - 600 Max x 4 @ 2 Ohms, 300 Max x 4 @ 4 Ohms, 1200 Max Bridged x 2 @ 4 Ohms. Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
Variable High-Pass Crossover - Speakers reproduce sound based on high, low or mid-range frequencies. A variable high pass crossover gears specifically towards “highs” such as all size speakers including mid ranges and tweeters
Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels. Specs - Dimensions: 17” x 10” x 2.4”, Weight: 12.15 lbs.
Power - 300 Max x 2 @ 2 Ohms, 150 Max x 2 @ 4 Ohms, 600 Max Bridged x 1 @ 4 Ohms
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
Power - 1000 Watts Max x 2 @2-Ohms, 500 Watts Max x 2 @4-Ohms, 2000 Watts Max x 1 Bridged @4 Ohms
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
$109.95
This website uses cookies to provide a better and more relevant experience. By clicking “Accept”, you consent to the use of ALL the cookies.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. One of the primary functions of these cookies is to temporarily store location data based on your internet address. This allows us to show you more geographically relevant best seller lists & products from Amazon.
We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
